Now Available pfsense 2.4.5 Upgrade. New Features and Changes

1 Like

Just as an FYI to those on these forums, the update failed on my SG-5100.
The short story is the installer said there was no space on my firewall and crashed. Then the firewall became unresposive both the web gui and it stopped routing. I hard rebooted it and everything came up (after I forced an fsck in single user mode, no less) and everything started to work…but the DHCP service won’t start. It also appears that I am stuck between versions. It says I’m on FreeBSD 11.3 but st the same time it says I’m on 2.4.4u3.
image

Below is my post to Netgate Support

This is a good reason to run pfSense as a virtual appliance since you can take a snapshot before any upgrade and if it blows up just run a snapshot restore.

When I run into issues, doing a reload and restore from backup works well. Everything is in the XML download.

1 Like

Just as an update:
They did end up sending me the firmware files the other night and I was able to recover the XML (I had a backup copy of the config anyway) and seamlessly reinstall the OS on my firewalll without re-doing my entire config or doing an upload of my backup.
Everything seems to be working correctly now, so it appears that the EMMC storage was not the culprit as I suspected might be the case, it was definitely a glitch in the update process.

I do have an m.2 drive on the way, so I will probably re-install again and set it up with a ZFS mirror between the EMMC and the m.2 drive.

@FredFerrell

Exactly my line of thinking when utilizing xcp-ng as the host. However I realize many don’t want to virtualize their router for various reasons.

After watching the video I decided to do the upgrade to my 5 month old sg-1100. Sadly now I have a brick. I attaced a console port and watched the boot process , I can’t say it made a lot of sense (no pun intended) to me but it complains of memory being full and this;

sa
Password:
Login incorrect
login:
login: admin
Password:
Login incorrect
login: netgate
Password:
Login incorrect
login: netgate
Password:
Login incorrect

login: login: login: login:
login: admin
Password:
Login incorrect
login: admin
Password:
Login incorrect
admin

^Clogin:
login: admin
Password:
Login incorrect

^C

adminlogin: login: login: login: login: admin
Password:
Login incorrect
login: admin
Password:

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 614 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

  1. Logout (SSH only) 9) pfTop
  2. Assign Interfaces 10) Filter Logs
  3. Set interface(s) IP address 11) Restart webConfigurator
  4. Reset webConfigurator password 12) PHP shell + pfSense tools
  5. Reset to factory defaults 13) Update from console
  6. Reboot system 14) Enable Secure Shell (sshd)
  7. Halt system 15) Restore recent configuration
  8. Ping host 16) Restart PHP-FPM
  9. Shell

Enter an option: 15

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 647 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 648 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

  1. Logout (SSH only) 9) pfTop
  2. Assign Interfaces 10) Filter Logs
  3. Set interface(s) IP address 11) Restart webConfigurator
  4. Reset webConfigurator password 12) PHP shell + pfSense tools
  5. Reset to factory defaults 13) Update from console
  6. Reboot system 14) Enable Secure Shell (sshd)
  7. Halt system 15) Restore recent configuration
  8. Ping host 16) Restart PHP-FPM
  9. Shell

Enter an option: 2

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 681 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 682 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

  1. Logout (SSH only) 9) pfTop
  2. Assign Interfaces 10) Filter Logs
  3. Set interface(s) IP address 11) Restart webConfigurator
  4. Reset webConfigurator password 12) PHP shell + pfSense tools
  5. Reset to factory defaults 13) Update from console
  6. Reboot system 14) Enable Secure Shell (sshd)
  7. Halt system 15) Restore recent configuration
  8. Ping host 16) Restart PHP-FPM
  9. Shell

Enter an option: 4

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 715 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 716 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

  1. Logout (SSH only) 9) pfTop
  2. Assign Interfaces 10) Filter Logs
  3. Set interface(s) IP address 11) Restart webConfigurator
  4. Reset webConfigurator password 12) PHP shell + pfSense tools
  5. Reset to factory defaults 13) Update from console
  6. Reboot system 14) Enable Secure Shell (sshd)
  7. Halt system 15) Restore recent configuration
  8. Ping host 16) Restart PHP-FPM
  9. Shell

Enter an option: 16

Killing check_reload_status
Killing php-fpm
pkill: Cannot open pidfile `/var/run/php-fpm.pid’: No such file or directory
Failed to fully fault in a core file segment at VA 0x41cf8000 with size 0x11000 to be written at offset 0xa71000 for process php-cgi
pid 772 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Failed to fully fault in a core file segment at VA 0x41bc0000 with size 0x11000 to be written at offset 0xa28000 for process php-cgi
pid 883 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Starting php-fpm
Failed to fully fault in a core file segment at VA 0x41f73000 with size 0x11000 to be written at offset 0xb1e000 for process php-fpm
pid 998 (php-fpm), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)
Starting check_reload_status

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 1002 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

  1. Logout (SSH only) 9) pfTop
  2. Assign Interfaces 10) Filter Logs
  3. Set interface(s) IP address 11) Restart webConfigurator
  4. Reset webConfigurator password 12) PHP shell + pfSense tools
  5. Reset to factory defaults 13) Update from console
  6. Reboot system 14) Enable Secure Shell (sshd)
  7. Halt system 15) Restore recent configuration
  8. Ping host 16) Restart PHP-FPM
  9. Shell

Enter an option: 4

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 1035 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 1036 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

  1. Logout (SSH only) 9) pfTop
  2. Assign Interfaces 10) Filter Logs
  3. Set interface(s) IP address 11) Restart webConfigurator
  4. Reset webConfigurator password 12) PHP shell + pfSense tools
  5. Reset to factory defaults 13) Update from console
  6. Reboot system 14) Enable Secure Shell (sshd)
  7. Halt system 15) Restore recent configuration
  8. Ping host 16) Restart PHP-FPM
  9. Shell

Enter an option: e6000sw0port2: link state changed to UP
2

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/local/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 1069 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/local/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 1070 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

  1. Logout (SSH only) 9) pfTop
  2. Assign Interfaces 10) Filter Logs
  3. Set interface(s) IP address 11) Restart webConfigurator
  4. Reset webConfigurator password 12) PHP shell + pfSense tools
  5. Reset to factory defaults 13) Update from console
  6. Reboot system 14) Enable Secure Shell (sshd)
  7. Halt system 15) Restore recent configuration
  8. Ping host 16) Restart PHP-FPM
  9. Shell

Enter an option: Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/local/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 1070 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/local/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/lib/php/20170718/intl.so.so”)) in Unknown on line 0
F
sa
Password:
Login incorrect
login:
login: admin
Password:
Login incorrect
login: netgate
Password:
Login incorrect
login: netgate
Password:
Login incorrect

login: login: login: login:
login: admin
Password:
Login incorrect
login: admin
Password:
Login incorrect
admin

^Clogin:
login: admin
Password:
Login incorrect

^C

adminlogin: login: login: login: login: admin
Password:
Login incorrect
login: admin
Password:

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 614 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

  1. Logout (SSH only) 9) pfTop
  2. Assign Interfaces 10) Filter Logs
  3. Set interface(s) IP address 11) Restart webConfigurator
  4. Reset webConfigurator password 12) PHP shell + pfSense tools
  5. Reset to factory defaults 13) Update from console
  6. Reboot system 14) Enable Secure Shell (sshd)
  7. Halt system 15) Restore recent configuration
  8. Ping host 16) Restart PHP-FPM
  9. Shell

Enter an option: 15

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 647 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 648 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

  1. Logout (SSH only) 9) pfTop
  2. Assign Interfaces 10) Filter Logs
  3. Set interface(s) IP address 11) Restart webConfigurator
  4. Reset webConfigurator password 12) PHP shell + pfSense tools
  5. Reset to factory defaults 13) Update from console
  6. Reboot system 14) Enable Secure Shell (sshd)
  7. Halt system 15) Restore recent configuration
  8. Ping host 16) Restart PHP-FPM
  9. Shell

Enter an option: 2

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 681 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 682 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

  1. Logout (SSH only) 9) pfTop
  2. Assign Interfaces 10) Filter Logs
  3. Set interface(s) IP address 11) Restart webConfigurator
  4. Reset webConfigurator password 12) PHP shell + pfSense tools
  5. Reset to factory defaults 13) Update from console
  6. Reboot system 14) Enable Secure Shell (sshd)
  7. Halt system 15) Restore recent configuration
  8. Ping host 16) Restart PHP-FPM
  9. Shell

Enter an option: 4

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 715 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 716 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

  1. Logout (SSH only) 9) pfTop
  2. Assign Interfaces 10) Filter Logs
  3. Set interface(s) IP address 11) Restart webConfigurator
  4. Reset webConfigurator password 12) PHP shell + pfSense tools
  5. Reset to factory defaults 13) Update from console
  6. Reboot system 14) Enable Secure Shell (sshd)
  7. Halt system 15) Restore recent configuration
  8. Ping host 16) Restart PHP-FPM
  9. Shell

Enter an option: 16

Killing check_reload_status
Killing php-fpm
pkill: Cannot open pidfile `/var/run/php-fpm.pid’: No such file or directory
Failed to fully fault in a core file segment at VA 0x41cf8000 with size 0x11000 to be written at offset 0xa71000 for process php-cgi
pid 772 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Failed to fully fault in a core file segment at VA 0x41bc0000 with size 0x11000 to be written at offset 0xa28000 for process php-cgi
pid 883 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Starting php-fpm
Failed to fully fault in a core file segment at VA 0x41f73000 with size 0x11000 to be written at offset 0xb1e000 for process php-fpm
pid 998 (php-fpm), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)
Starting check_reload_status

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 1002 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

  1. Logout (SSH only) 9) pfTop
  2. Assign Interfaces 10) Filter Logs
  3. Set interface(s) IP address 11) Restart webConfigurator
  4. Reset webConfigurator password 12) PHP shell + pfSense tools
  5. Reset to factory defaults 13) Update from console
  6. Reboot system 14) Enable Secure Shell (sshd)
  7. Halt system 15) Restore recent configuration
  8. Ping host 16) Restart PHP-FPM
  9. Shell

Enter an option: 4

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 1035 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/loca l/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/ lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 1036 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

  1. Logout (SSH only) 9) pfTop
  2. Assign Interfaces 10) Filter Logs
  3. Set interface(s) IP address 11) Restart webConfigurator
  4. Reset webConfigurator password 12) PHP shell + pfSense tools
  5. Reset to factory defaults 13) Update from console
  6. Reboot system 14) Enable Secure Shell (sshd)
  7. Halt system 15) Restore recent configuration
  8. Ping host 16) Restart PHP-FPM
  9. Shell

Enter an option: e6000sw0port2: link state changed to UP
2

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/local/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 1069 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/local/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 1070 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

  1. Logout (SSH only) 9) pfTop
  2. Assign Interfaces 10) Filter Logs
  3. Set interface(s) IP address 11) Restart webConfigurator
  4. Reset webConfigurator password 12) PHP shell + pfSense tools
  5. Reset to factory defaults 13) Update from console
  6. Reboot system 14) Enable Secure Shell (sshd)
  7. Halt system 15) Restore recent configuration
  8. Ping host 16) Restart PHP-FPM
  9. Shell

Enter an option: Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/local/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/lib/php/20170718/intl.so.so”)) in Unknown on line 0
Failed to fully fault in a core file segment at VA 0x41f4f000 with size 0x11000 to be written at offset 0xb1e000 for process php-cgi
pid 1070 (php-cgi), jid 0, uid 0: exited on signal 11 (core dumped)
Segmentation fault (core dumped)

Warning: PHP Startup: Unable to load dynamic library ‘intl.so’ (tried: /usr/local/lib/php/20170718/intl.so (Shared object “libicui18n.so.65” not found, required by “intl.so”), /usr/local/lib/php/20170718/intl.so.so (Cannot open “/usr/local/lib/php/20170718/intl.so.so”)) in Unknown on line 0
F
it seem I’ve made a mess. Can anybody suggest how to proceed.

thanks in advance

I’m sorry it copyed more than I intended…after the update it all reported success until the reboot came which kept trying but never happened. Clearly I have much to learn about this product.

If you’re still having an issue, I would reinstall the firmware from scratch. https://docs.netgate.com/pfsense/en/latest/solutions/sg-1100/reinstall-pfsense.html

1 Like